GEOMETRIC DESIGN OF STAGES IN NICKEL LATERITE ORE MINING IN PIT ARJ02 PT CERIA NUGRAHA INDOTAMA, WOLO DISTRICT, KOLAKA REGENCY

Authors

  • Arifuddin Arifuddin
  • Deniyatno Deniyatno Halu Oleo University
  • Irfan Saputra Halu Oleo University
  • Asri Arifin Halu Oleo University

Keywords:

mine geotechnics, safety factor, slope recomendation

Abstract

Mining activities often experience problems that originate from geotechnical problems that cause changes in the stress distribution on the slope which results in disruption of slope stability and can eventually cause landslides. To express the level of stability of a slope, the term Safety Factor is known. The value of the safety factor of mine slopes in Indonesia is regulated in the Decree of the Minister of Energy and Mineral Resources No. 1827 K/30/MEM of 2018 concerning Guidelines for the Implementation of Good Mining Engineering Rules. This research aims to provide recommendations for stable and optimal mining slope geometry based on the physical and mechanical properties of the soil that makes up the slope in the pit diamond mining plan of PT Ceria Nugraha Indotama. The method used in determining slope stability in this study is the Bishop Simplified method. The results showed the simulation of slope stability on the profile of nickel laterite deposits under conditions of distributed additional load by the Caterpillar PC 350 excavator of 47 kN/m2 and the influence of earthquake vibration of 0,2 gal. For a single slope as high as 5 meters, the Saprolite layer in dynamic conditions with an angle of 40o and a Bench width of 2 meters is the material that has the lowest FK value, namely FK= 1,454 with PL = 0,00% so that it can represent all materials as the most pessimistic condition and is used as a reference for designing the overall slope geometry with a maximum height of 45 meters. Based on the results of the study, it can be concluded that the recommendation for mining slope geometry uses the overall slope geometry with a maximum height of 45 meters, a bench width of 2 meters, with FK in dynamic conditions of 1,242 and PL= 0,00% and an overall slope angle of 36o

References

Fadli, F. 2016.Desain Pit Penambangan Batubara Blok C Pada PT.. Intibuana Indah Selaras Kabupaten Nunukan Provinsi Kalimantan Utara. Jurnal Geomine, 1(1), 55–63.

Turangan, V. G. M., Pangeman, A. E., & Sompie, O. B. A. 2014. Analisis Kestabilan Lereng Dengan Metode Fellenius. Jurnal Sipil Statik, 21, 37–46.

Pane, R. A., & Anaperta, Y. M. 2020. Karakterisasi Massa Batuan dan Analisis Kestabilan Lereng Untuk Evaluasi Geometri Lereng di Pit Barat Tambang Terbuka PT.. AICJ (Allied Indo Coal Jaya) Kota Sawahlunto Provinsi Sumatera Barat. Jurnal Bina Tambang, 4(3), 218–232.

Awal, R., Prabowo, E., & Zubir, A. 2020. Evaluasi Kestabilan Lereng Pit 2 Tambang Batubara Pada PT Semula Prima Coal Di Desa Rangkiling Kecamatan Mandiangin Kabupaten Sarolangun Provinsi Jambi. Joulnal Mine Magazine , 1(1).

Hardiyatmo. 2020. Mekanika tanah 2. Suparyanto Dan Rosad (2015, 5(3), 248– 253.

Nasution, S. N., Rachman, S., & Pramudito, H. (2021). Slope stability analysis using bishop method and kinematic analysis. IOP Conference Series: Materials Science and Engineering, 1098(6), 062041.

Sutasoma, M., Susilo, A., & Suryo, E. A. (2017). Penyelidikan Zona Longsor dengan Metode Resistivitas dan Analisis Stabilitas Lereng untuk Mitigasi Bencana Tanah Longsor. Indonesian Journal of Applied Physics, 7(1), 35

Haryadi, D., Mawardi, M., & Razali, M. R. (2019). Analisis Lereng Terasering Dalam Upaya Penanggulangan Longsor Metode Fellenius Dengan Program Geostudio Slope. Inersia, Jurnal Teknik Sipil, 10(2), 53–60.

Menteri Energi dan Sumber Daya Mineral. 2018. Keputusan Menteri ESDM Nomor 1827 K 30 MEM 2018.

Published

2025-12-22